Unveiling the Culprits: Why Won’t My Jeep Start?

Why won't my jeep start. Image of a vehicle.
Why won’t my jeep start? Image from Fields Chrysler Jeep Dodge Ram’s blog.

Why won’t my Jeep start?

Jeep has been an iconic & legendary 4×4 sport utility vehicle for the past 70 years. 

It is a very powerful vehicle.

No one wants to think about starting their car only to find that it isn’t working. That’s not fun at all. 

The most common reasons for a Jeep not starting are a dead battery, a damaged alternator, a faulty starter, or a faulty ignition switch. A clogged fuel filter or a faulty fuel pump are two other common culprits.

What would cause a jeep not to start?

Sometimes the issue with your car is just but a simple fix that doesn’t require a mechanic. 

Below are some of the common reasons why your car won’t start, as well as possible fixes.

  • Gas Issues.

Running out of gas is more common than you think. 

After all, do you know how far you can drive once the “E” appears on your dashboard? 

  • Dead Battery.

Is there a clicking sound when you turn the key? 

Are your lights and stereo working?

If not then your battery may be completely dead. 

For this, you can take out your battery and try charging at an automotive store or get it tested to diagnose the issue.

Fully charged automotive batteries should measure 12.6 volts or above.

When the engine is running, this measurement should be 13.7 to 14.7 volts.

  • Corroded battery terminals.

Corroded terminals may prevent your jeep from starting. 

To figure this problem out, take out your battery and check on the battery cables for rust or dirt. 

Clean up the dirt, reconnect the terminals and try restarting your vehicle.

  • Faulty starter.

If your battery is very healthy but your starter isn’t working, you cannot start your Jeep.

A faulty ignition switch may also prevent your vehicle from starting.

  • Faulty spark plugs.

When a spark plug fires, it transfers voltage from the ignition coil pack to the cylinder head, resulting in a spark that ignites the fuel and starts your vehicle. 

If your spark plugs are not firing, it could be another factor contributing to why your jeep wrangler won’t start.

Image of spark plugs
Why won’t my jeep start? Image source: car from japan blog.
  • Bad starter solenoid. 

This is one of the electrical components of the starter. 

When your ignition switch sends a signal to the starter solenoid, it activates the starter motor. 

If this isn’t working, you’ll need to check the fuses and, if necessary, replace them.


Why is my Jeep not starting but has power?

It can be aggravating to be sitting behind the wheel of your Jeep Wrangler and having trouble starting it. 

When the car appears to have power but the engine refuses to start, the problem becomes much more confusing. 

This is a common problem that frequently leaves you baffled as to the root of the problem. 

Luckily, there are a few things you may look into, and one of them is most likely the culprit. 

To transmit power to various systems and components, many Jeep models, including the Wrangler, rely on a component known as a totally integrated power module (TIPM). 

When the TIPM fails, one of the obvious symptoms is the engine cranking but not starting.

A malfunctioning ignition switch can fail randomly and unpredictably.

This is another possible explanation for your Wrangler having power but failing to start. 

When your problem of having power but not starting becomes irregular and unpredictable, you may have reason to believe that your car has been possessed by an evil spirit. 

However, there is a reasonable explanation for this mysterious condition, changing your TIPM or ignition switch should fix the problem.

Frequently asked questions

Why a Jeep won’t start when hot?

When it is hot outdoors, Jeep owners may experience that their cars will not start. 

It’s a tremendous pain when your Jeep’s engine refuses to start due to heat and you’re already on the road. 

Starter failure, dead batteries, a faulty fuel pump, a fuel injector issue, a faulty spark plug, and other factors are all possible causes of your Jeep’s inability to start when it’s hot. 

The most common source of this problem is a faulty Jeep starter. 

The starter’s ability to perform properly deteriorates as its temperature rises. 

Because of this, the Jeep will not start. 

In this case, replacing the faulty starter with a new one will resolve the problem.

Why is my Jeep cranking but not starting?

It is not very common for the Jeep to crank but not start. Is this your problem?

When you try to start your Jeep, the cranking sounds indicate that the starter is functioning properly. 

The most likely causes in this case are a damaged spark plug, a faulty crankshaft position sensor, a faulty fuel pump, low compression, and a fuel injector malfunction. 

Why won’t my Jeep start with a new battery?

The first step is to inspect the wiring connecting the battery to the starter.

The voltage drop across the starter circuit should be investigated. 

They should also inspect the starter and the neutral safety switch. 

The second issue could be that the key fob is worn out. 

When it doesn’t start the next time, press the key fob against the start button. 

If the car starts, there is a problem with the fob.

Why won’t my jeep start no power at all?

The most common causes of a Jeep losing power are problems with the fuel system or the Jeep battery. 

Other common causes include computer, sensor, and wiring problems, faulty alternators, or exhaust problems.

Begin by ensuring that the battery is charged and that the engine is receiving fuel.


The text discusses various reasons why a Jeep may not start and provides possible explanations for each scenario. 

It mentions common issues such as a dead battery, damaged alternator, faulty starter, faulty ignition switch, clogged fuel filter, or

faulty fuel pump. 

The text also addresses specific situations, such as a Jeep cranking but not starting, a Jeep not starting when hot, or a Jeep not starting despite having a new battery

It suggests troubleshooting steps like checking battery connections, inspecting the starter circuit, examining the key fob, and ensuring fuel supply.



Leave a Comment